Cement And Concrete Testing Equipment

Approx. Rs 48,000 / UnitGet Latest Price

Product BrochureProduct Details:

Specification: 

• The Flexure Strength Testing Machines are designed to provide maximum rigidity throughout their working range. The load is applied by the upward movement of a hydraulic ram. The jack can be raised or lowered for testing different size beams. The load is indicated on a calibrated Bourdon tube type Pressure Gauge of range: 0-100kN x 0.5kN (0-10,000 kgf x 50 Kgf). The load gauge is calibrated against NPL/ NCCBM certified proving ring.

Approx. Rs 15,500 / PieceGet Latest Price

Product BrochureProduct Details:

Standards: ASTM C 469

Specification: Consists of a frame with a bottom ring and a top ring with tightening screws to firmly clamp the compressometer over the cylinder. A dial gauge .002 mm x 5 mm is mounted on the upper ring and the tie of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw. Supplied in a wooden carrying case. 

Approx. Rs 18,000 / PCSGet Latest Price

Product BrochureProduct Details:

Standards: ASTM C 232; EN 480-4

Specification: Used for the compaction of concrete samples in a mould. Generally the vibratory hammer is found to be a much faster & quicker method as compared to impact hammering. The vibratory hammers are supplied with 1 tamping feet & 1 shank. Used for determination of the relative quantity of mixing water that will bleed from a sample of freshly mixed concrete.

Approx. Rs 6,000 / PieceGet Latest Price

Product BrochureProduct Details:

Standards: EN 12350-9

Specification: The L Shape box is used for determining the passing ability rate of freshly mixed self compacting concrete. The distance between 12 mm diameter bars can be set between 41±1 mm or 59±1 mm. L Shape box is designed for ease of cleaning the vertical and horizontal hoppers.

The l shape box apparatus is supplied complete with:

Filling Hopper

Base

Approx. Rs 5,500 / UnitGet Latest Price

Product BrochureProduct Details:

Standards: EN 12350-5

Specification: The test set is used for concrete mixes of high workability and determines flow index as an arithmetic mean of the diameter of the specimen after working on a flow table. The apparatus consists of a double steel table, an upper table measuring 700 x 700 mm and hinged at one side to the lower table. The top table is inscribed and all parts are protected against corrosion. The stainless steel cone has a 130 ±2 mm top diameter, 200 ±2 mm base diameter and 200 ±2 mm height and 1.5 mm thickness.

Approx. Rs 29,000 / PieceGet Latest Price

Product BrochureProduct Details:

Product Description:

• Standards: IS 516, BS 1881
• Specification: The load frame is made up of high quality steel construction with a fixed. Upper lead carrying a ball seated platen. 4 pillars are fixed to the base and the top plate of the loading frame. The upper and lower plates are adjusted with the help of head screw on either side of the pillar. The ram dia of the machine varies from the requirements of the customer. The lower pattern are at the base of the frame above the ram and it is rectangular in shape. Sufficient clearance is provided between the platens to fit in the cylindrical/ cube moulds. Spacer provided to adjust cubes and cylinders. A 20 cm dia. pressure gauge with maximum load induction pointer is fitted on the top panel and in turn is connected to the hydraulic pressure pipe.
• Ranges: 50 kN to 3000 kN

Approx. Rs 3,800 / PieceGet Latest Price

Product BrochureProduct Details:

Standards: BS 1881-108

Specification: Made of Cast Iron / Mild Steel. The mould are made of 4 plates assembled together. Each mould is supplied complete with base plate. Faces are machined flat to ± 0.2mm. And finished in size to 0.2mm.

• Beam Mould 100mm x 100mm x 500mm
• Beam Mould 150mm x 150mm x 700mm

Approx. Rs 6,000 / UnitGet Latest Price

Product BrochureProduct Details:

Standards: EN 12350-9

Specification: The V Funnel apparatus is used to evaluate the flow time of freshly mixed self compacting concrete. The test is not suitable when the maximum size of the aggregate exceeds 22.4 mm.

The test set consists of a stainless steel funnel placed vertically on a supporting stand. The discharge orifice is equipped with a lid, which can be momentarily opened. The 

Approx. Rs 52,000 / PieceGet Latest Price

Product BrochureProduct Details:

Specification:

• 24 Hour cycle from time of mixing.
• Controlled 35° C or 100° C ± 2° C Curing Temperature for concrete.
• Controlled 27° C ± 2° C Curing Temperature for grey cement.
• The tank has been designed to accommodate 150mm / 70.6mm cube moulds upto 36/72 cube mould and fully insulated, complete with a hinged lid, heater, thermostat and re-circulated pump. Provision of two removable racks allowing free circulation of water around each mould. The pump, drain valves and electrical equipment are housed in a compartment located at one end of the tank. The Tank is heated by an immersion heater under normal conditions and refrigeration system for grey cement the temperature is controlled at 35° C or 100° C ± 2° C / 27° C +2° C, expect for the 15 minutes after immersion of the freshly made specimens

Note: Accelerated curing tank with cooling arrangement is also available of request.

• Curing Tank for 6/12 moulds of 150 mm / 70.6 mm size
• Curing Tank for 12/24 moulds of 150 mm / 70.6 mm size
• Curing Tank for 24/48 moulds of 150 mm / 70.6 mm size
• Curing Tank for 36/72 moulds of 150 mm / 70.6 mm size

Approx. Rs 6,500 / PieceGet Latest Price

Product BrochureProduct Details:

Standards: EN 12350-12

Specification: 

• The J-Ring test is used for determining the passing ability, the flow spread and the flow time of self compacting concrete as the concrete flows through the J-Ring apparatus. The J-Ring narrow gap with ø18 mm x 16 smooth bars is manufactured from stainless steel.
• The Slump Cone is made from sheet steel protected against corrosion, with diameters; top 100 mm, base 200 mm and with a height of 300 mm. The Base plate is 900x900x3 mm square, made of stainless steel with engraved circles of 200 mm and 500 mm diameter conforming to EN 12350- 8.
• The Steel weighted collar is used to stabilize the slump cone on J-Ring or slump flow tests.
• Minimum apparatus for the J-Ring test are J-Ring with narrow gap and slump cone.
• SMEW-0080 J-Ring, narrow gap
• SMEW-0080 Slump cone for J-Ring
• SMEW-0080-A Base plate for J-Ring and slump-flow tests
• SMEW-0080-B Steel weighted collar, 9 kg
• SMEW-0080-C EN 12350-8 for slump cone on J-Ring or slump flow test

Approx. Rs 9,500 / UnitGet Latest Price

Product BrochureProduct Details:

Model No.: SMEW-0096

Specification: The unit consists of two movable frames pivoted at one end. The extensometer is fixed to the specimen with the help of tightening screws. The lateral extension is indicated on a dial gauge of 0.002 mm x 5 mm is mounted on the upper ring and the tip of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw. Supplied in a wooden carrying case.