S.M.Engineering Works

Product Description:

• Specification: The concrete permeability apparatus comprises of a mild steel cell of Square/Round cross-section mounted on a stand and a pressure chamber is connected to the cell through copper tubing and T-connector mounted on the stand with sleeve packed valve and rubber hose pipe with end connections. The cell assembly consists of one base plate and one top plate connected to nozzles.
• Note: The pressure chamber is fitted with a pressure regulator which helps in regulating the pressure from 0-15kg/cm sq. Gauge is for indicating the pressure in the cell. A foot pump and a pressure tube is supplied to develop pressure in the chamber. The apparatus is supplied with a measuring cylinder 500cc to measure percolated quantity to water.
• Pressure can also be applied; by a pressure air line or by a compressor (2 HP capacity), can be supplied at an extra cost.
• Model available for 3,6, 9, 12, 18 cells permeability also.

• Standards: IS 1199 & BS EN 12350
• Specification: The instrument is used for workability as well as consistency of fresh concrete. A slump Cone and a graduated rod supplied with the instrument helps the operator to find out slump values and vibration table with container and acrylic disc is used to find out workability of concrete expressed in Vee Bee degrees, which is defined as the time in seconds to complete required vibrating at which the fresh concrete flows out sufficiently to come in contract of the entire face of acrylic disc.
• The equipment consists of : A vibrating table size 380 mm long and 260 mm wide, resting upon elastic support at a height of about 305 mm above the floor, complete with Start/Stop switch, cord and plug. A holder is fixed to the base in to which a swivel arm is telescoped with funnel and guide swivel arm is also detachable from the vibrating table. The divisions of scale on the rod record the slump of the concrete in millimeters. Supplied complete with a sheet metal container with lifting handles which can easily be fixed to the vibrating table. A slump cone open at both ends with lifting handles and a tamping rod of size 16 mm dia. and 600 mm long rounded at both ends.

• Standards: IS 7320 & BS 1881-102
• Specification: SE-Test India manufactures slump test apparatus for gauging the consistency of concrete mixes. Slump test is really important to find out the characteristics of freshly mixed concrete and needs to be performed without fail. Our apparatus conforms to the international standards and industry best practices and allows engineers and technicians to assess the concrete properties relating to cohesion and mixing consistency ‘on site’ in least of time. Every batch of concrete can be checked easily without any lags thus saving the project timelines.

Slump Test Apparatus Product specifications –

• The apparatus can be used for concrete mixes with maximum aggregate size of 38 mm.
• There is a slump cone made of steel. Its lower base diameter is 200 mm while at the top, it has diameter of 100 mm. Height is 300 mm.
• Foot pieces can be fixed to the clamps provided at the base plate. A lifting handle is also attached with the base plate for easy handling
• A 600 mm long and 16 mm wide graduated steel rod is provided as part of the apparatus.
• Slump test apparatus of SE-test India is developed as per standards IS 7320 and BS 1881 – 102.
• Our apparatus is of very simple make yet it has been developed through the use of best quality materials including high tensile steel that is rust proof. Thus the apparatus delivers without any deformity or lack of accuracy for years.

• Note: Table top size : 750 x 750 mm & 1000 x 1000 mm also available at an extra cost. Both models operates on 440 volts, A.C. Three Phase

Product Description: We are specialized in the Manufacturing and Supplying of Cylindrical Mould. The Cylindrical Mould is used for testing concrete cylinders for compressive strength tests. The Cylindrical Mould can be availed at market leading prices from us.

Product Specifications -

• The mould is made as split type with two equal segments that can be combined accurately
• Base plate and top plate are offered together with cylinder. Fasteners are also provided
• Base plate and top plate are machined flat to +/- 0.03 mm
• Mean diameter (internal) of the moulds is within the accuracy range of +/- 0.2 mm
• Height of the metal cylindrical mould is within accuracy range of +/- 1 mm
• Mould cylinder, cast iron, 150mm dia. x 150mm height.
• Mould cylinder, cast iron, 150mm dia. x 300mm height.
• Mould cylinder, cast iron, 160mm dia. x 320mm height.
• Mould cylinder, cast iron, 100mm dia. x 200mm height.
• Mould cylinder, cast iron, 300mm dia. x 600mm height.

Product Description:

• SE-Test India manufactures cylindrical moulds of metal for specimen testing and analyses of concrete columns. We make cylindrical moulds in standard sizes that are widely used by the civil engineering labs in India and world for testing the compression, linearity, stability and other essential attributes of concrete columns. The moulds are delivered high quality finish at its inner surface to ensure that best specimens are derived without any imperfection. Our cylindrical mould (Model SET 1119) is developed with high grade steel and cast iron material that offer strength and durability, especially the rust and corrosion resistance. The dimensional make of the moulds is such that deformation is negligible even after continued and regular use of them.

Product Specifications -

Find the objective specifications of metal cylindrical moulds of SE-Test India here below –

• The mould is made as split type with two equal segments that can be combined accurately
• Base plate and top plate are offered together with cylinder. Fasteners are also provided
• Base plate and top plate are machined flat to +/- 0.03 mm
• Mean diameter (internal) of the moulds is within the accuracy range of +/- 0.2 mm
• Height of the metal cylindrical mould is within accuracy range of +/- 1 mm

Cylindrical moulds of SE-Test India are made with highest precision & these serve well the demands of engineers and technicians. Our moulds can be used easily on site to make the specimens.

• Mould cylinder, cast iron, 150mm dia. x 150mm height.
• Mould cylinder, cast iron, 150mm dia. x 300mm height.
• Mould cylinder, cast iron, 160mm dia. x 320mm height.
• Mould cylinder, cast iron, 100mm dia. x 200mm height.
• Mould cylinder, cast iron, 300mm dia. x 600mm height.

Product Description:

• Standards: IS 1199, 5515. & BS 1881-103
• Specification: SE-Test India manufactures compaction factor apparatus that has been designed as per the international standards and requirements of construction industry. The apparatus allows determining the workability of different types of concrete mixes by assessing the compaction ratio. Having a simple set up, the compaction factor apparatus performs stably and is guaranteed for high durability. It can be used ‘on site’ and the workability of the concrete mix could be easily determined in less of time.

Compaction Factor Apparatus Product specifications: Compaction factor apparatus from SE-Test India has the following specifications

• The apparatus is made as a rigid metallic frame that has two conical hoppers and one cylinder at its base
• The conical hoppers have hinged trapdoors with quick release catchers at the lower end
• The cylinder top is covered with a circular metal plate
• A plaster trowel and a metal rod rounded at both ends (600 mm in length and 16 mm in diameter) is also provided
• Our compaction factor apparatus has been developed with the best quality materials like stainless steel and delivered appropriate finishing and dimensional accuracy to ensure precise results for the engineers and technicians. The compaction factor apparatus conforms to the standards IS 1199 and 5515 and BS 1881 – 103.

• Standards: IS 3085, DIN 1048
• Specification: The concrete permeability apparatus comprises of a mild steel cell of Square/Round cross-section mounted on a stand and a pressure chamber is connected to the cell through copper tubing and T-connector mounted on the stand with sleeve packed valve and rubber hose pipe with end connections. The cell assembly consists of one base plate and one top plate connected to nozzles.
• Note: The pressure chamber is fitted with a pressure regulator which helps in regulating the pressure from 0-15kg/cm sq. Gauge is for indicating the pressure in the cell. A foot pump and a pressure tube is supplied to develop pressure in the chamber. The apparatus is supplied with a measuring cylinder 500cc to measure percolated quantity to water.
• Pressure can also be applied; by a pressure air line or by a compressor (2 HP capacity), can be supplied at an extra cost.
• Model available for 6, 9, 12, 18 cells permeability also.

• Standards: IS 1199 1959 & BS 1881-106
• Specification: The apparatus consists of a pressure tight flanged cylindrical measuring bowl. The bowl is fitted with a removable flanged conical cover assembly with the help of a seal. The conical cover has an air valve and a petcock for bleeding off the water. A transparent cylindrical stand pipe which is graduated in air content is fixed to the conical cover assembly. Pressure is applied to the specimen with the help of a pressure bulb and the pressure is recorded on the pressure gauge which is mounted on the stand pipe. The whole assembly is mounted on a flat base. The instrument is supplied complete with one each following accessories.
• Calibration cylinder with spring clamp, trowel, tamping rod, straight edge. Rubber mallet and measure.

Capacity Are also Available

• Bowl Capacity: 0.005 cubic meter
• Bowl Capacity: 0.007 cubic meter
• Bowl Capacity: 0.01 cubic meter
• Bowl Capacity: 0.01 cubic meter

Standards: ASTM C 469

Specification: Consists of a frame with a bottom ring and a top ring with tightening screws to firmly clamp the compressometer over the cylinder. A dial gauge .002 mm x 5 mm is mounted on the upper ring and the tie of the dial gauge rests on an anvil. The zero on the dial gauge can be set by adjusting the anvil screw. Supplied in a wooden carrying case. 

Product description:

Specification: We are providers of Vibratory Hammers, which is a specialized equipment used consistently at construction sites. The Vibratory Hammer is electrically operated. Our Vibratory Hammer has several uses. Some of them are listed below. Specifications Used for changing the soil formation with the use of its vibration Used for driving hammers into heavy or hard piles Used for the compaction of concrete cubes of 150mm & 100mm.